麻豆xfplay国产在线观看_亚洲AⅤ日韩久久久xyz_女生阴道被男生插在线观看_欧美精品一区二区三区在线视频_欲色a∨人人爽网站hd播放器_最新国产在线观看福利_100款不良网站进入窗口软件_农村乱淫视频免费_亚洲永久免费播放片app一_一级特大a黄片播放视频

　　Hollow glass in the production process, there is a key link, is to use structural glue to completely seal two pieces of glass, because manual gluing is slow, sealing is not good, so a large number of production hollow glass need hollow glass gluing machine, the following will take you together to understand the hollow glass gluing machine debugging methods.

　　1、打開中空玻璃打膠機的氣泵開關,電源總開關,控制臺開關,在控制臺按手動按鈕,然后在顯示屏上找到原點設定,點擊輔助原點設定,然后點擊頭部原點設定,注意原點設定時避免頭部和輔助吸盤碰撞.設定好之后返回設定玻璃厚度,輸入完以后,點擊設置進入.等命令位置和當前位置數值一致即可

　　1. First, turn on the air pump switch, the main power switch and the console switch of the hollow glass gluing machine, press the manual button on the console, then find the origin setting on the display screen, click on the auxiliary origin setting, then click on the origin setting of the head, pay attention to the origin setting to avoid collision between the head and the auxiliary sucker. After setting, return to the setting glass thickness, after input, click on the setting to enter. The position and the current position are identical.

　　2、打開桶膠按鈕,按工作選擇拍膠啟動,在按伐開.此時膠頭已經出膠,等看不見白膠,以混均勻以后按伐關,在按鏈接生產線,此時可以自動打膠.開始打膠要看每條邊每個角打膠是否均勻

　　2. Open the first bucket of glue button, press the choice of work to start the glue tapping, and press the cutting. At this time, the glue head has been glued, so that no white glue can be seen, after mixing evenly, press the cutting off, in the link production line, at this time, you can automatically glue. Start gluing depends on whether each side and corner is even glued.

　　3、如果需要調整打膠機的壓力,可以在屏幕上點擊返回找到密封配方,會顯示當前密封壓力,如果每條邊都缺膠,那么可增加壓力,壓力大膠量大,壓力小膠量就小.如果發現某條邊膠量不夠時,在密封配方中會顯示有向上密封,上部密封,向下密封,和下部密封,開始打膠的那條邊就是向上密封,然后順序從上

　　3. If you need to adjust the pressure of the glue beater, you can click back on the screen to find the sealing formula, which will show the current sealing pressure. If there is a lack of glue on each side, it will increase the pressure. If there is a large amount of glue on each side, the small amount of glue on the pressure will be small. The edge is sealed up, and then the order is from top to bottom.

　　4、如果發下只有某條邊膠少或膠多時,調整掃描膠量細微調整,數值大膠量就大,數值小膠量就小.然后說下到末端伐關的距離,數值大,膠嘴到末端膠量少,數值小膠量大

　　4. If only one side glue is less or more, fine adjustment of scanning glue amount will result in a large amount of glue and a small amount of glue.