自動灌膠機設備出現漏氣現象怎么辦？
自動灌膠機設備是專門針對流體進行控制的設備，自動化設備取代人工操作是企業生產改革的必然趨勢，自動化程度的高低，一定程度上影響了企業的發展速度和企業的管理水平。自動灌膠機設備主要針對的流體就是膠水，膠水的種類有分為很多，有單組份膠水和雙組份膠水，在實際的點膠操作過程所應用的點膠工藝也會有很大的不同。針對微量控膠需求的設備一般都被稱為自動點膠機，雙組份膠水一般多用作填充、灌封等，用膠量比較大，需要實現膠水的配比混合，所以這類設備被稱為雙液灌膠機。
The automatic glue filling machine is a kind of equipment which is specially designed to control the fluid. It is an inevitable trend that the automatic equipment replaces the manual operation in the production reform of the enterprise. The level of automation, to a certain extent, affects the development speed and management level of the enterprise. The main fluid of the automatic glue filling machine is glue. There are many kinds of glue, including single component glue and two-component glue. The dispensing process applied in the actual dispensing operation process will also be very different. The equipment for micro glue control is generally called automatic dispensing machine, and the two-component glue is generally used for filling, filling and sealing, etc., with a large amount of glue, so it is necessary to realize the mixing of glue ratio, so this kind of equipment is called double liquid glue pouring machine.
自動灌膠機設備的主要控膠動力可以分為氣動和電動。氣動就是以壓縮空氣來實現，調節氣壓的大小來達到點膠需求；還有就是電動，電動以點快干膠為主。這里主要介紹以氣動作為主要?jiǎng)恿Φ脑O(shè)備，點膠機如果在使用的過程中出現漏氣現象，就會直接影響點膠的質量。如果出現了漏氣現象，需要先分析是什么原因造成的漏氣，然后在根據實際情況進行解決。
The main glue control power of automatic glue filling machine can be divided into pneumatic and electric. Pneumatic is to achieve compressed air, adjust the size of air pressure to meet the dispensing demand; there is also electric, electric to point quick drying rubber. This paper mainly introduces the pneumatic equipment as the main power. If the dispensing machine leaks in the use process, it will directly affect the dispensing quality. If there is air leakage, it is necessary to analyze what causes the air leakage, and then solve it according to the actual situation.
自動灌膠機壓力桶如果出現漏氣現象，可以通過檢查漏氣的位置，然后進行判斷，壓力桶的漏氣都為鎖緊螺絲沒有上緊，還有就是壓力桶桶蓋和桶體之前的密封點出現破損，具體的解決辦法就是更換密封墊，鎖緊螺絲。如果是輸氣管漏氣的話，直接更換就可以了，要檢查是不是有磨損或者嚴重的對折，如果氣壓過大的話，在對折處可能會爆掉。如果是氣管與氣管之間的轉接頭出現漏氣，那就需要進行更換轉接頭。如果是控制器里面的電磁閥出現了故障，就需要進行更換了。具體的點膠機漏氣可以從以上幾個地方進行檢查。
If there is air leakage in the pressure barrel of the automatic rubber filling machine, you can check the position of the air leakage, and then judge. The air leakage of the pressure barrel is that the locking screw is not tightened, and the sealing point before the barrel cover and the barrel body is damaged. The specific solution is to replace the sealing gasket and lock the screw. If there is air leakage in the gas transmission pipe, it can be replaced directly. Check whether there is abrasion or serious fold. If the air pressure is too high, it may explode at the fold. If the adapter between the air pipe and the air pipe leaks, the adapter needs to be replaced. If the solenoid valve in the controller fails, it needs to be replaced. Specific dispenser air leakage can be checked from the above several places.
上一篇：點膠機的針頭與膠水使用時應該注意啥？
下一篇：自動點膠機膠體粘度對產品的影響！
