麻豆xfplay国产在线观看_亚洲AⅤ日韩久久久xyz_女生阴道被男生插在线观看_欧美精品一区二区三区在线视频_欲色a∨人人爽网站hd播放器_最新国产在线观看福利_100款不良网站进入窗口软件_农村乱淫视频免费_亚洲永久免费播放片app一_一级特大a黄片播放视频

1.打膠機：針頭和塞子的彎曲或磨損會對點膠質量產生重大影響。如果溫度高或長時間不清洗，貼片膠也可能在針頭內表面固化或半固化，造成堵塞。定期檢查打膠機頭，發現污染，及時清理。將針頭浸泡在兼容的溶劑中是一種常見的方法，但單獨浸泡的效率太低，無法去除所有未固化的材料?？梢杂眉嫒萑軇┑母邏簢婌F將膠水從針頭內孔吹出，然后用干燥的壓縮空氣將膠水吹出內孔，使針頭干燥。

1. glue applicator: the bending or wear of the needle and plug will have a significant impact on the dispensing quality. If the temperature is high or it is not cleaned for a long time, the patch adhesive may also solidify or semi solidify on the inner surface of the needle, causing blockage. Regularly check the glue applicator head, and clean it up in time if any pollution is found. Soaking the needle in a compatible solvent is a common method, but soaking alone is too inefficient to remove all uncured material. The glue can be blown out of the inner hole of the needle with a high-pressure spray of compatible solvent, and then the glue can be blown out of the inner hole with dry compressed air to dry the needle.

2、金屬模板：為了避免清潔劑侵蝕模板和絲網的粘合劑，使用預洗工藝，使用更強的清潔劑，手動操作，避免清潔劑和粘合劑接觸，然后清洗模板用普通洗滌劑。

2. Metal formwork: in order to avoid the adhesive of formwork and wire mesh eroded by detergent, use pre washing process, use stronger detergent, operate manually to avoid the contact between detergent and adhesive, and then clean the formwork with common detergent.

3、塑料網板：清洗塑料網板時，可能會發生靜電放電。因此，應使用特殊的抗靜電清潔劑來避免這種現象。同時，不要用抹布用手清潔，因?yàn)樗芰虾苋菀讋潅?，長此以往可能會造成打印質量問題。點膠機的清潔是點膠機日常維護中的一項重要工作。用戶對此非常重視，但清潔方法仍需改進。

3. Plastic screen: electrostatic discharge may occur when cleaning the plastic screen. Therefore, special antistatic cleaners should be used to avoid this phenomenon. At the same time, do not use a rag to clean by hand, because the plastic is easy to scratch, which may cause printing quality problems in the long run. The cleaning of dispensing machine is an important work in the daily maintenance of dispensing machine. Users attach great importance to this, but the cleaning method still needs to be improved.

4、雙組份打膠機出膠時，應有一定成分，使新膠管中的膠水能順利流出膠頭。公認膠閥的壓力和速度是按理想情況設定的。然后測量膠體流速，直到連續兩次測量的誤差在計劃的正負2%范圍內。

4. When the two-component glue applicator delivers glue, it should have certain ingredients to make the glue in the new hose flow out of the glue head smoothly. It is generally accepted that the pressure and speed of the rubber valve are set according to the ideal situation. Then measure the colloid flow rate until the error of two consecutive measurements is within the planned range of plus or minus 2%.

其余還應注意，如遇以下情況，建議不要使用粗略的純膠管更換方法：膠管內的膠水在點膠機運行過程中已經用完。在這種情況下，分配閥很可能有大氣。軟管中的膠水已超過使用時間。在上述情況下，您需要徹底清潔剛性分配閥或分配泵，并按照設備程序進行操作。

It should also be noted that in the following cases, it is recommended not to use the rough replacement method of pure rubber hose: the glue in the hose has been used up during the operation of the dispenser. In this case, the distribution valve is likely to have atmosphere. The glue in the hose has expired. In the above cases, you need to thoroughly clean the rigid distribution valve or distribution pump and follow the equipment procedures.

5、快干膠（速干膠）堵在灌膠機膠閥的連接頭和管路上：這種情況主要是體內水分過多或快干膠多次重復使用，應使用新鮮的速干膠。對于干膠，用體內不含水分的甲苯徹底清洗管道。應用的氣體應徹底干燥，過濾裝置應在出廠時在氣壓和閥門系統軟件之間進行修改。

5. The quick drying glue (quick drying glue) is blocked on the connector and pipeline of the glue valve of the glue dispenser: This is mainly due to excessive water in the body or repeated use of the quick drying glue. Fresh quick drying glue should be used. For dry glue, thoroughly clean the pipe with toluene that does not contain water in the body. The applied gas shall be thoroughly dried, and the filtering device shall be modified between the air pressure and the valve system software at the factory.

以上就是今天為大家分享的關于問題的相關內容，希望對大家能有所幫助，想要了解更多內容可以電話聯系我們或者關注我們的網站http://dejiansw.cn。

The above is the relevant content about the problem shared for you today. I hope it can help you. If you want to know more, you can contact us by phone or follow our website http://dejiansw.cn 。