打膠機日常使用一定要知道這幾點
一般情況下,能夠正確的使用機器,一方面能夠做好產品,另一方面也可以延長機器的使用壽命,保持機器的性能穩定持久。使用
雙組份打膠機也是如此,下面簡單的說明一下,主要有以下幾點:
In general, if you can use the machine correctly, on the one hand, you can do a good job of the product, on the other hand, you can extend the service life of the machine and keep the performance of the machine stable and lasting. The same is true for the two-component sealant dispenser. The following is a brief description, mainly including the following points:
1、使用機器前,確保電源電壓的穩定以及電路,保證機器在開機中正常運行。
1. Before using the machine, ensure the stability of the power supply voltage and the safety of the circuit, and ensure the normal operation of the machine during startup.
2、確保機器的各工件都處入原點位置,機器上沒有雜物,以免阻擋機器運行,
2. Make sure that all the workpieces of the machine are at the original position, and there are no sundries on the machine, so as not to block the operation of the machine,
3、經常給機器的滑輪處加黃油,保證門窗打膠機的滑輪潤滑,運轉時更流暢,
3. Add grease to the pulley of the machine frequently to ensure that the pulley of the door and window gluing machine is lubricated and runs more smoothly,
4、機器正在工作時,看看周圍的人是否在的距離,以免機器在工作時傷害到旁邊的人。
4. When the machine is working, check whether the people around are at a safe distance to prevent the machine from harming the people around.
5、開機前請先關閉總電源開關,再接通控制開關(on);
5. Please turn off the main power switch before starting the machine, and then turn on the control switch (on);
6、按啟動按鈕,待電機轉動后即可進行作業。如遇緊急情況時請立即按下停止鍵停機;
6. Press the start button to start the operation after the motor rotates. In case of emergency, please immediately press the stop button to stop the machine;
7、工作過程中如發現異?,F(xiàn)象應立即關機切斷總開關電源、拔出插頭或更換相應保險絲后再重新開機運行操作.
7. In case of any abnormal phenomenon during operation, shut down the power supply of the main switch immediately, pull out the plug or replace the corresponding fuse, and then restart the machine for operation
在工作中應隨時注意觀察電機的運轉狀況是否正常、有無異響等異?,F(xiàn)象發生。如有故障出現時應立即停機處理以免造成人身傷害和設備損壞。更多相關事項就來我們網站
http://dejiansw.cn咨詢了解吧!
During the operation, pay attention to whether the motor operates normally and whether there is abnormal noise and other abnormal phenomena. In case of any fault, stop the machine immediately to avoid personal injury and equipment damage. Come to our website for more information http://dejiansw.cn Ask and understand!
上一篇:打膠機的主要技術參數以及結構原理
下一篇:必不可少的打膠機使用過程中關注兩點